What to Look for When Choosing a Screen Printing Machine
17 November 2026 · 15 min read · Arus Makina
Manual, semi-automatic and fully automatic machines compared; a buyer's guide covering print size, table, registration, squeegee system, safety and service.
A screen printing machine is an investment that a workshop or factory will use for years. A poorly chosen machine either falls short of the capacity you need and slows the work down, or is larger and more complex than necessary and never pays for itself. To choose well, you have to look at the job first, not the machine: what will you print on, at what size, how many pieces a day and with which ink? In this article we set out the questions to ask when buying a screen printing machine and the differences between machines, from a viewpoint that is independent of any seller.
Define your job first
Before you compare machine quotations, putting the answers to the questions below in writing makes life easier both for you and for the company that will be quoting:
- Material: is it glass, plastic sheet, metal, cardboard, textile, wood or some other surface? Is the material rigid, flexible or fragile?
- Largest and smallest size: what are the width, length and thickness of the largest piece you will print? Which size do you print most often?
- Print area: does the design cover the whole piece, or only a particular part of it?
- Number of colours: are your jobs single-colour or multi-colour? Is precise fit between the colours required?
- Quantity: how many prints do you aim to produce per day or per shift? Will that figure rise in the coming years?
- Ink: will you be using solvent-based, water-based, UV, two-component or ceramic (fired) ink? The answer determines the drying system directly.
- Space and infrastructure: what floor area is available for the machine and the drying line, and what electrical power and compressed air supply do you have?
Once the answers to these questions are clear, most of the machine options rule themselves out.
Machine types: manual, semi-automatic, fully automatic
Manual benches
On a manual bench, lowering the screen, pulling the squeegee and loading and unloading the material are all the operator's job. The initial investment is low, and it is adequate for small-format, short-run work. However, print quality depends on the operator's hand; pressure and speed vary a little with every pull. As the format grows, it becomes harder to pull the squeegee evenly, and fatigue brings quality down.
Semi-automatic machines
On a semi-automatic machine the operator places the material on the table and removes it after printing; lowering the screen, the flood stroke and the print stroke are carried out by the machine. Squeegee pressure, angle and speed are set once, and every print is repeated with the same values. This makes quality noticeably more consistent, particularly on large formats and on jobs with solid areas. Semi-automatic machines are the class most often chosen by businesses with medium-scale production, because they sit at a balanced point between investment cost and capacity.
Three-quarter automatic and fully automatic lines
On a three-quarter automatic machine, feeding is done by hand, and after printing the material is taken off by the machine and transferred to a conveyor or a conveyor drying tunnel. On fully automatic lines, feeding, alignment, printing, drying and stacking are linked together and the operator simply monitors the line. These lines make sense for high-volume production that runs continuously at the same size; in workshops where jobs change frequently, set-up time can eat into the gain.
Flatbed, cylindrical and carousel
The construction of the machine varies with the shape of the material to be printed:
- Flatbed screen printing machines: for flat and mostly rigid materials such as glass, sheet, panels and cardboard. The material rests on a fixed table and the screen comes down onto it.
- Cylindrical (round) printing machines: for cylindrical or conical items such as bottles, glasses and tubes. The item rotates on its own axis during printing.
- Carousels: used in textile printing. The pallets rotate, arriving beneath each colour station in turn.
- Roll-to-roll machines: for continuous materials such as labels and flexible film.
The rest of this article focuses mainly on flatbed screen printing machines, because this is the class most widely used for large-format industrial work.
Print size and screen size
The two most frequently confused figures for a machine are the maximum print area and the maximum screen size. The print area is the area over which the squeegee can actually pass ink. The screen, on the other hand, has to be larger than the print area in every direction, because a margin is needed for the squeegee to stop and lift, for the ink to rest and for the mesh to stretch. On large formats this margin grows as well.
When choosing a size, bear the following points in mind:
- Choose the machine not for the largest piece you print today, but for the largest piece you expect to print over the next few years. A machine's size cannot be increased later.
- A machine that is larger than necessary is also a cost: it takes up more space, calls for larger screens and more ink, and set-up takes longer on small pieces.
- Ask whether the table's height adjustment is sufficient for the thickness of your material. Thin film and thick glass may not fit within the same adjustment range.
The print table and holding the material in place
The material must not move during printing. The most common solution for this is a vacuum table: air is drawn through small holes in the table surface and the material is held down against the table. Vacuum is indispensable particularly for lightweight materials such as paper, film and thin plastic. For heavy materials such as glass and thick sheet, register pins and edge stops come to the fore.
Questions to ask about the table:
- Is the table surface flat and rigid? On large tables, any deviation in flatness changes the thickness of the print.
- Can vacuum zones be shut off? When printing small pieces, holes left uncovered reduce the suction.
- How does the material reach the table and how does it leave? With large, heavy pieces, conveyor or belt feeding reduces both the load on the operator and the risk of breakage.
- After printing, will the piece be carried to the drying tunnel by hand, or will the machine transfer it directly? Carrying a wet print by hand is slow and also carries a risk of smudging.
Registration: aligning the colours and the piece
Registration means that the design lands in the same place on the material every time and, on multi-colour jobs, that the colours sit exactly on top of one another. Registration depends on two things: the position of the material on the table and the position of the screen in the machine.
On the material side, corner and edge stops, pins or, on automatic lines, sensor-based alignment systems are used. On the screen side, fine adjustment of the screen holders matters: micro-registration adjustment screws that can shift the screen left and right, forwards and backwards and rotationally in small steps cut set-up time considerably. On a machine without micro-registration adjustment, aligning the screen by pushing and pulling it by hand both takes time and fails to give a precise result.
The squeegee and flood system
The part of a semi-automatic machine that does most to determine print quality is the squeegee head. The things to examine are as follows:
- Pressure adjustment: is squeegee pressure set pneumatically or mechanically? Is the adjustment gauged and repeatable?
- Angle adjustment: can the angles of the squeegee and the flood bar be changed independently?
- Speed adjustment: can the print and flood speeds be set separately? Inks of different viscosity call for different speeds.
- Stroke length adjustment: can the squeegee's start and end points be shortened to suit the length of the design? Sweeping the whole table for a small design is a waste of time.
- Squeegee change: can the squeegee and the flood blade be removed and fitted easily? This time becomes important at colour changes.
Before the print stroke, the flood bar spreads the ink over the design in a thin layer. In this way the open mesh apertures fill with ink and drying-in on the screen is delayed. Flooding that does not work properly is one of the most common causes of incomplete prints.
Off-contact distance and how the screen lifts
The gap between the screen and the material should be adjustable, and it should be possible to make this adjustment equally at all four corners of the screen. On large-format prints one further feature becomes important: peel-off, where the screen lifts progressively from the rear in step with the squeegee's travel. This allows the mesh to separate cleanly from the material immediately behind the squeegee; ink does not smear onto the underside of the screen and the edges stay sharp. If you are buying a machine with a large table, be sure to ask whether it has this feature and whether it is adjustable.
The control system
On current machines the movements are managed by a PLC and settings are made from a touchscreen panel. A good control system provides the following:
- Entry of values such as print and flood speed, dwell times and stroke length on the screen.
- Saving the settings for frequently repeated jobs as recipes and recalling them.
- Operating modes such as single print, continuous print and double stroke.
- A clear on-screen indication of the fault when something goes wrong.
- A print counter.
The language of the panel, the simplicity of the menus and how quickly an operator can learn the machine should also be taken into account. A complicated interface is an invitation to error at shift changes.
Matching the drying line
A printing machine is not a production line on its own; a drying stage always follows it. Leaving drying as a separate matter to be dealt with later when choosing the machine is a common mistake. Points to watch:
- The hourly capacity of the printing machine and the capacity of the drying tunnel should be matched to one another. If the tunnel is too slow, the printing machine waits.
- The height of the print table and the height of the tunnel conveyor should be level with each other, and pieces should be transferred without jolting.
- The belt width of the tunnel should be chosen to suit the largest piece to be printed.
- The drying method suited to the ink to be used (hot air, infrared or UV) should be decided at the outset.
- If the pieces leaving the dryer are to be stacked, a cooling section is needed at the end of the tunnel.
Buying the printing machine and the drying tunnel from the same manufacturer, sized to suit one another, prevents compatibility problems that might otherwise arise later.
Safety and standards
On screen printing machines, the moving screen, the squeegee head and the conveyors present a trapping hazard for the operator. Check whether the machine has the following:
- Emergency stop buttons that are easy to reach.
- A safety bar or light curtain that protects the operator's hand as the screen comes down.
- Appropriate fuses and residual current protection in the electrical cabinet.
- Protective guards over moving transmission parts.
- A CE declaration of conformity and an operating manual in Turkish.
Safety equipment is not an item to be bargained over; under occupational health and safety legislation it is the employer's responsibility.
Service, spare parts and training
The true cost of a machine does not end with the purchase price. When the machine stops, production stops too; that is why after-sales support matters as much as the technical specification. When obtaining a quotation, ask the following:
- Are installation and commissioning included in the price?
- Is operator training provided, and how long does it last?
- What are the length and scope of the warranty?
- Are spare parts held in stock, and how long do they take to arrive?
- Are the motors, drives, PLC and pneumatic components used in the machine from brands that are readily available on the market?
- In the event of a breakdown, how quickly can a service engineer be on site?
A machine that uses parts from standard, well-known brands remains repairable years later.
New or second-hand?
Second-hand machines are attractive for their low prices, but they carry certain risks: worn guides and bearings reduce registration accuracy, parts for old control systems may be unobtainable, and there is no way of knowing how the machine was used in the past. If you are going to buy second-hand, be sure to see the machine running, make a test print with your own screen, and check the flatness of the table and the play in the squeegee head. With a new machine, on the other hand, the warranty, the training and the option of having it sized to your work are what you get in return for the difference in price.
How should you compare quotations?
Ranking quotations from different companies by price alone is misleading. Make the comparison under the same headings: maximum print area, maximum screen size, table type, the adjustment options of the squeegee system, control system, safety equipment, drying line, delivery time, installation, training and warranty. If possible, see the machine at the place where it is built or at a business where it is in use, and ask for a test print with a sample from your own work. A test print gives you information that no figure in a catalogue can.
Calculating the return on investment
Rather than judging the machine's price in isolation, it is sounder to look at how the machine will change the cost of a print. For a simple calculation, list the following items one beneath the other:
- The number of prints the machine can realistically deliver per hour. The basis should be not the maximum speed in the catalogue but the achievable speed, including loading, unloading and inspection times.
- The number of people needed to run the machine.
- The time spent fitting the screen and setting up at a job change.
- The waste rate: material and ink thrown away because of faulty prints.
- Electricity and compressed air consumption.
- Annual maintenance and consumables costs.
When you compare these values with the way you work at present, it becomes clear how much the new machine will save per print and in how many months the investment will pay for itself. With large, expensive materials, glass for example, even a small fall in the waste rate can be a bigger gain than the saving in labour. Doing the calculation with cautious rather than optimistic figures prevents disappointment later on.
Preparing the infrastructure before the machine arrives
For the machine to be able to start work on the day it arrives at the workshop, certain preparations need to be completed beforehand:
- Layout: in addition to the dimensions of the machine and the drying tunnel, sufficient clearance should be left around them for fitting and removing screens, feeding the material, stacking and carrying out maintenance. With large-format materials, access for a forklift or trolley is also taken into account.
- Floor: the floor should be level and able to bear the weight of the machine. The machine is levelled on its adjustable feet; a table that is not level affects the thickness of the print.
- Electricity: a supply line, distribution board and earthing suited to the total power of the machine and the tunnel should be ready. Drying tunnels draw far more power than the printing machine.
- Compressed air: the pneumatic components need dry, clean air. The capacity of the compressor and the pressure in the line should meet the values the manufacturer asks for.
- Ventilation: if you will be working with solvent-based inks, ventilation of the printing area and of the tunnel exhaust should be planned.
- Access route: which door the machine will come into the workshop through, and on what vehicle, should be checked before delivery. Machines with large tables may not pass through standard doors.
Common purchasing mistakes
The same mistakes are made again and again when buying a machine. Knowing them is the easiest way to avoid them:
- Looking only at the price: a cheap machine can soon prove expensive because of set-up time and waste.
- Choosing the size for today's work: buying a new machine in order to move up a size is far more expensive than choosing the right size at the outset.
- Leaving drying until later: once the printing machine has arrived, it may turn out that the drying tunnel does not fit or that its capacity is not enough.
- Deciding without seeing a test print: a trial made with your own material and ink is the most reliable evidence.
- Not asking about service: whether a company that is attentive at the time of sale can also be reached when there is a breakdown can be found out by asking businesses that serve as its references.
- Not involving the operator in the process: the opinion of the person who will use the machine every day is the most valuable information on ease of use.
Conclusion
The right screen printing machine is not the most expensive one or the one with the most features, but the one that best suits your work. Once you have clearly defined your material, your size, your quantity and your ink, the options narrow quickly. Comparing the remaining candidates one by one under the headings of table, registration, squeegee system, controls, safety and service, and making sure you see a test print, will let you reach a decision you will not regret for years.
At Arus Makina we offer large-format flatbed screen printing machines and the conveyor drying tunnels that work in the same line with them. Write to us with the material and size you will be printing, and we will prepare the configuration that suits you and a price quotation.
Which machine fits your work?
Tell us what you print and at what size, and we will send a suitable model and a quote.
Request a Quote