What Is Screen Printing and How Does It Work? A Step-by-Step Guide from Screen to Drying
17 November 2026 · 15 min read · Arus Makina
How screen printing works, screen preparation, choosing mesh and squeegee, ink types, press settings and common faults, in one guide.
Screen printing is a printing technique in which ink is forced through the openings of a finely woven mesh onto the substrate with the help of a squeegee. It is also known as silk screen printing, serigraphy or stencil printing. The reason it is used across such a wide field, from textiles to glass and from packaging to electronics, is simple: it can print on almost any surface, with a thick, opaque layer of ink, and the print lasts. In this guide we explain, in order, how screen printing works, which steps a job goes through from screen preparation to drying, and the settings that determine print quality.
How does screen printing work?
The heart of screen printing is the screen. A screen consists of a fine mesh fabric stretched over an aluminium or steel frame. The areas of the mesh that are not to print are blocked with a light-sensitive emulsion, while the areas that are to print are left open. The screen is positioned over the substrate, ink is placed inside the screen, and a flexible blade called a squeegee is pulled across the screen from one end to the other. As the squeegee passes, it presses the mesh down onto the substrate and pushes the ink through the open mesh. Once the squeegee has passed, the mesh lifts away from the substrate and leaves behind a layer of ink in the shape of the design.
This simple mechanism has two important consequences. First, the amount of ink is determined largely by the mesh itself: the thicker the mesh and the more open its apertures, the more ink passes onto the substrate. Second, during printing the screen and the substrate touch only along the narrow line where the squeegee is pressing. This is what allows screen printing to work on surfaces that are uneven, rigid, fragile or textured.
How screen printing differs from other printing techniques
Offset, flexo and digital printing leave a thin film of ink. In screen printing the ink layer is noticeably thicker than with these techniques. The thick layer brings the following advantages:
- Opaque, vivid colours are achieved even on dark backgrounds.
- Prints can be made that withstand outdoor conditions, abrasion and washing.
- Special inks can be used, such as conductive, adhesive, raised, gloss, matt, phosphorescent or glitter inks.
- Very different materials, such as glass, metal, wood, ceramic, plastic, fabric and board, can be printed with the same method.
On the other hand, screen printing requires a separate screen for each colour, and on photographic-quality work with very fine halftones it may not be as fast or as economical as offset or digital printing. For this reason screen printing is generally chosen for jobs with few colours and solid areas, or where durability or a special effect is required.
Where is screen printing used?
Screen printing is used far more widely than is generally assumed. The main areas are as follows:
- Textiles: T-shirts, sweatshirts, sports kit, cotton bags and cut-piece printing.
- Glass: architectural glass, furniture and decorative glass, glass for white goods, the edge bands of automotive glass, and bottle and drinking-glass printing.
- Advertising and signage: acrylic, PVC, foam PVC board, aluminium composite panels, posters and stickers.
- Packaging: cartons, plastic containers, cosmetics packaging, spot varnish and special-effect applications.
- Industrial printing: membrane keypads, front panels, labels, measuring rules and equipment housings.
- Electronics: printed circuit boards, conductive tracks and the conductive lines of solar panels.
- Ceramics and decoration: tiles, decals and transfer prints.
In each of these areas the substrate, the ink and the machine are different; the basic steps, however, are the same.
The screen printing process step by step
1. Design and film preparation
A print job begins with the design. In multicolour work the design is separated into its colours and a separate film (positive) is prepared for each one. On the film, the areas that are to print must be fully black and opaque to light; grey or semi-transparent areas cause problems during exposure. The thickness of fine lines and small type must be chosen to suit the mesh count that will be used.
2. Mesh selection and stretching
Mesh is woven from polyester threads or, for more demanding work, stainless steel threads, and is defined by the number of threads per centimetre. Coarse meshes let a lot of ink through and suit coarse detail; fine meshes let little ink through and give fine detail. The mesh is stretched onto the frame at an even tension on a stretching machine and glued in place. Tension that is balanced in every direction and does not drop over time is decisive for registration (the colours sitting exactly on top of one another). A slack screen causes the design to shift in printing and produces blurred edges.
3. Degreasing, emulsion and drying
The stretched mesh is first cleaned with a degreaser; dust and grease on it prevent the emulsion from adhering. The light-sensitive emulsion is then applied to both sides of the mesh in a thin, even layer using a scoop coater. The coated screen is dried in a horizontal position in a dust-free, dark (or yellow-lit) environment. At this stage the screen must not be exposed to light.
4. Exposure and washout
The film is placed on the dried screen and exposed to ultraviolet light in an exposure unit. Vacuum exposure units press the film tightly against the screen, which improves edge sharpness. The emulsion hardens in the areas that receive light, while the emulsion lying beneath the black areas of the film remains soft. After exposure the screen is washed out with water, the emulsion that has stayed soft rinses away and the design opens up. Exposure time is determined by the type of emulsion, the thickness of the coating, the mesh count and the power of the light source; the most accurate time is found with an exposure test. An underexposed screen breaks down during printing, and on an overexposed screen fine details close up.
5. Retouching and mounting the screen on the machine
Pinholes in the dried screen are sealed with screen filler and the edges are taped. The screen is mounted on the machine and aligned to the substrate to be printed. In multicolour work the registration of each screen is set individually.
6. Printing
Ink is placed inside the screen. First the flood bar spreads the ink over the design in a thin layer, then the print squeegee is pulled across under pressure and transfers the ink to the substrate. On semi-automatic and automatic machines these two movements are carried out by the machine, in the same way every time, at the speed and pressure that have been set.
7. Drying and curing
The substrate coming off the press is dried. The drying method depends on the type of ink: solvent-based and water-based inks are hardened with hot air, plastisol inks with heat and UV inks with ultraviolet light. In volume production this is done in conveyor drying tunnels connected to the delivery end of the printing machine.
8. Cleaning and reclaiming the screen
When the job is finished, the ink is removed from the screen with a suitable cleaner. If the screen is going to be used again it is stored; if not, the emulsion is removed with a stencil remover and the mesh is prepared for a new job.
How to choose the mesh count
Mesh count is expressed as the number of threads per centimetre. The right count depends on three things: the type of ink, the fineness of the design and the ink thickness required. As a general guide:
- Coarse meshes of roughly 15 to 40 threads per centimetre are used for glitter and raised effects and for jobs requiring a very thick deposit.
- Medium meshes of roughly 43 to 77 threads are common in textile printing and in general work with solid areas.
- Meshes of roughly 90 to 120 threads are for fine type and detailed designs.
- Very fine meshes of roughly 140 threads and above are preferred for UV inks and for halftone and very fine work.
These values are a starting point. For the final choice, refer to the mesh range recommended in the ink manufacturer's technical data sheet.
Squeegee selection and settings
The squeegee is a polyurethane blade, and its hardness is stated on the Shore A scale. Soft squeegees of roughly 60 to 65 Shore lay down a lot of ink and conform to textured surfaces. Medium squeegees of 70 to 75 Shore are general purpose. Hard squeegees of 80 Shore and above lay down little ink and give a sharp edge on fine detail.
Four squeegee settings have a direct effect on the printed result:
- Pressure: the lowest pressure that is enough to pass the ink through the mesh is ideal. Excess pressure spreads the design and wears out the mesh and the squeegee.
- Angle: the more upright the squeegee, the less ink reaches the substrate; the flatter it is, the more.
- Speed: a fast stroke leaves less ink, a slow stroke more. With inks that flow poorly, the speed is reduced.
- Edge condition: a nicked or rounded squeegee edge causes streaks and unevenness in the print. Squeegees should be sharpened or replaced regularly.
Why does off-contact distance matter?
In screen printing the screen does not sit in full contact with the substrate; a gap of a few millimetres is left between them. This gap is called the off-contact distance, or snap-off. As the squeegee passes it brings the mesh into contact with the substrate, and immediately after it has passed the mesh lifts away from the substrate under its own tension. If this release is not clean, ink smears onto the underside of the screen and the edges of the design are spoiled.
If the gap is too small, the mesh stays stuck to the substrate and the print smears. If it is too large, the design stretches, registration is lost and the mesh wears out early. On large-format screens the gap is set larger than on small screens. On flatbed printing machines, having the screen lift progressively from the rear in step with the squeegee makes a clean release easier on large formats.
Screen printing inks
Ink is chosen according to the substrate to be printed and the environment in which the print will be used. The main groups of ink are as follows:
- Solvent-based inks: used on many surfaces such as plastic, metal, glass and paper. They dry by evaporation of the solvent and require ventilation.
- Water-based inks: used particularly in textile and paper printing. They give a soft handle and need care to stop them drying in the screen.
- Plastisol inks: the most widely used ink in textile printing. They do not dry in air and are cured with heat, which means they can be worked in the screen for a long time.
- UV inks: harden within seconds under ultraviolet light. They contain no solvent or very little, and are common in plastic, glass and packaging printing.
- Two-component inks: used with the addition of a hardener. They provide high adhesion and chemical resistance on glass, metal and difficult surfaces.
- Ceramic (fired) inks: fuse with the surface of glass and ceramic when fired at high temperature.
Whichever ink is chosen, the manufacturer's technical data sheet must be taken as the basis for thinner ratio, mixing, mesh range and drying conditions.
Common printing faults and their solutions
- Smearing and spreading at the edges: the squeegee pressure may be too high, the off-contact distance too small or the ink too thin. Reduce the pressure, increase the gap and check the viscosity of the ink.
- Incomplete print, unprinted areas: the ink may have dried in the screen, the pressure may be insufficient or the mesh too fine. Clean the screen, apply a flood stroke and, if necessary, use a coarser mesh.
- Sawtooth edges: the emulsion layer may be thin, or the mesh too coarse for the design. Try a finer mesh or a thicker emulsion.
- Colours out of register: the screen tension may be low, the off-contact distance too large or the substrate slipping on the print table. Measure the tension and check the vacuum and the lays.
- Pinholes: degreasing is inadequate or the environment is dusty. Retouch the screen before printing and keep the preparation area clean.
- Print scratching off or coming out in the wash: the ink is not suited to the surface or drying is inadequate. Review the ink and the drying temperature and time.
Manual, semi-automatic and automatic printing
Small quantities and small formats can be printed by hand. As quantity and format increase, pressure and speed in hand pulling vary from print to print, the operator tires and quality fluctuates. On semi-automatic machines the operator positions the substrate and the machine performs the flood and print strokes, so every print comes off at the same pressure, angle and speed. On fully automatic lines, feeding, printing, drying and stacking run linked together without operator intervention.
For large-format glass, sheet and panel printing, hand pulling is not practical; these jobs call for flatbed printing machines with large print tables and conveyor drying tunnels connected to their delivery end.
Screen tension and how it is measured
Screen tension is measured in newtons per centimetre, and a tension meter (tensiometer) is used for the purpose. Measurements are taken at the centre of the screen and at points close to the corners, in both the warp and the weft direction. It matters more that the values are close to one another than that each is individually high. For general work, tensions of roughly 15 to 25 newtons per centimetre are common; fine, precise work is run at higher values.
A newly stretched mesh loses tension in the first few hours. For this reason the screen is left to rest for a time after stretching, re-tensioned if necessary, and only then glued. The screens for the different colours of the same job should be close to one another in tension; otherwise each screen stretches by a different amount during printing and the colours do not register. On screens that have been in use for a long time, tension falls over time; regular measurement shortens the time spent hunting for the source of registration problems.
Colour sequence in multicolour printing
Where more than one colour is to be printed, the order in which the colours go down is planned in advance. The common approach is to work from light colours to dark ones; that way the dark colour covers any slight overrun at the edge of the light colour beneath it. When printing on a dark background, a white underbase is usually printed first, dried, and the other colours are printed on top of it. The underbase ensures that the colours above it look vivid.
Where colours butt up against each other, the edge of one colour is extended very slightly beneath the other so that no gap is left between them. This trap allowance is set according to the registration accuracy of the machine and the screens. After each colour, the print must be dried enough to go into the next colour; a colour printed over wet ink smears onto the underside of the next screen. This is why, in multicolour work, intermediate drying and cooling directly determine production speed.
The effect of the printing environment
The temperature, humidity and cleanliness of the screen printing workshop affect the result more than is generally assumed. In a warm, dry environment solvent-based and water-based inks dry faster in the screen and block the mesh openings; in a cool environment the ink thickens and flows less readily. Materials that absorb moisture, such as paper and board, change dimension with humidity, and in multicolour work this turns into a registration problem. Leaving the substrate to stand in the workshop for a time before printing reduces this effect.
Dust is the most stubborn enemy of screen printing. Dust that sticks to the emulsion during screen preparation produces pinholes; dust that falls on the substrate during printing is trapped beneath the ink. Separating the screen preparation area from the printing and cutting areas, wiping the substrate with a tack cloth before printing and cleaning the floor regularly are simple but effective precautions. In workshops where solvents are used, adequate ventilation is essential both for print quality and for the health of the workforce.
Checklist for starting a new job
- Obtain an ink suited to the substrate, together with its technical data sheet.
- From the mesh range recommended in the data sheet, choose the count that suits the fineness of the design.
- Measure the screen tension and verify the exposure time with a test.
- Set the squeegee hardness, angle and pressure, starting from the lowest values that are sufficient.
- Set the off-contact distance according to the format and make it equal at all four corners.
- Make a few test prints and dry them; carry out adhesion and resistance tests.
- Write down the settings that work and start from this record when the same job comes in again.
Conclusion
Screen printing is a technique that is simple in principle but rich in detail. A good print is the sum of the right mesh, a screen that has been properly stretched and correctly exposed, an ink suited to the job, balanced squeegee settings and adequate drying. When one of these links is weak, the problem usually shows up at a different stage, for example after drying or in the customer's hands. That is why the safest course is to make a small test print on every new job, note down the settings and work to the same recipe on subsequent jobs.
If you are looking for a screen printing machine or a drying tunnel suited to the substrate and size you will be printing, write to us; we will listen to what your work involves and decide on the right solution together.
Which machine fits your work?
Tell us what you print and at what size, and we will send a suitable model and a quote.
Request a Quote