MAKİNA

Drying in Screen Printing: A Guide to Conveyor Drying Tunnels

17 November 2026 · 15 min read · Arus Makina

Drying and curing methods by ink type, hot air, infrared and UV systems, conveyor speed, the cooling section and how to test that a print is dry.

In screen printing, the job is not finished the moment the squeegee has passed across the screen. The ink on the substrate is still wet: touch it and it smears, stack it and the sheets stick together, ship it before it has fully hardened and it will scratch off in the customer's hands or come out in the wash. The stage that decides how long a print lasts is drying. Because the ink film in screen printing is thick compared with other printing processes, drying also demands more energy, more time and more care. In this article we explain the drying methods suited to each type of ink, how conveyor drying tunnels work and what to look for when choosing the right tunnel.

Drying and curing are not the same thing

In everyday speech both are called drying, but technically they are different processes.

Drying is the removal of the liquid carrier in the ink, that is the solvent or the water, by evaporation. What remains is pigment and binder. Most solvent-based and water-based inks dry in this way.

Curing, on the other hand, is the hardening of the ink through a chemical or physical change. Plastisol ink gels and fuses under heat; UV ink polymerises under ultraviolet light; two-component inks react with a hardener to form cross-links. In curing, nothing needs to leave the ink; what is needed is for the right amount of energy to reach the whole of the ink film.

This distinction matters, because a print whose surface looks dry may not be cured. Prints that do not smear under a fingertip but lift when scratched with a fingernail, or crack in the first wash, are in most cases the result of incomplete curing.

Drying methods by ink type

Solvent-based inks

Solvent-based inks will also dry on their own at room temperature, but this can take minutes or even hours and is not suitable for volume production. In hot air tunnels, evaporation is accelerated. Here air movement matters as much as temperature: if the evaporated solvent builds up above the surface, drying slows down. For this reason the solvent-laden air in the tunnel has to be discharged to the outside through a flue. The heat resistance of the substrate sets the upper limit for temperature; thin plastic films and some sheet materials warp or shrink at high temperatures.

Water-based inks

Water evaporates less readily than solvents. Water-based inks need strong air circulation and sufficient tunnel length. In textiles, many water-based inks do not simply dry; they must also be fixed at a specific temperature for a specific time in order to gain wash fastness. If the moisture is not extracted from the tunnel, the air inside reaches saturation and drying stops.

Plastisol inks

Plastisol is the most widely used ink in textile printing and it does not dry in air. It cures when the whole of the ink film reaches the temperature specified by the manufacturer; for standard plastisols this is generally around 150 to 165 degrees Celsius, and lower for low-cure types. What matters is not the air temperature in the tunnel but the temperature reached by the ink itself. In thick prints, even when the surface reaches temperature, the bottom layer in contact with the fabric can remain cool; in that case the print cracks in the first wash.

UV inks

UV inks harden in less than a second under ultraviolet light. Because they are cured by light rather than heat, they have an advantage on heat-sensitive substrates. Conventional systems use mercury vapour lamps, while newer systems use LED UV sources. LED systems give off less heat, switch on and off instantly and have a long service life; however, the ink must be suited to the LED wavelength. In UV curing, the deciding factors are the power of the lamp and the speed at which the substrate passes beneath it.

Two-component and glass inks

Two-component inks used on surfaces such as glass and metal cure over time through the reaction of the hardener; heat accelerates this reaction and increases durability. Ceramic inks used in glass printing, by contrast, are first dried in the tunnel and then fuse with the surface at high temperature during the tempering or firing of the glass. In work of this kind, the task of the drying tunnel is to make the print touch-dry until it reaches the furnace or the next colour.

The exact temperature and time values for each ink are given in the manufacturer's technical data sheet, and these values should be taken as the basis.

How is heat transferred to the substrate?

In drying tunnels, heat is delivered in one of three ways or by a combination of them.

Hot air (convection)

Heated air is blown onto the substrate by fans. The heat is distributed evenly throughout, is little affected by colour or surface, and sweeps the evaporated solvent or moisture away from the surface. It is the most reliable method for solvent-based and water-based inks. Its weakness is that it transfers heat relatively slowly; this is why hot air tunnels are longer.

Infrared (IR)

Infrared heaters heat the substrate and the ink directly rather than the air. Heat transfer is fast, the tunnel can be kept shorter and the system reaches operating temperature quickly. On the other hand, the absorption of infrared radiation varies with colour: dark colours heat up more quickly than light ones. In multicolour work, therefore, care is taken to ensure that temperature is not distributed unevenly between the colours. Infrared heaters are generally used together with air circulation; the radiation heats, while the air carries away the vapour and evens out the temperature.

Ultraviolet (UV)

UV systems are used not to supply heat but to cure UV ink. They are useful only with inks that cure under UV; a UV lamp will not dry a solvent-based or water-based ink.

In practice many tunnels are of hybrid design: rapid heating with infrared first, then equalisation with hot air and finally cooling.

How does a conveyor drying tunnel work?

A conveyor drying tunnel is a machine that carries the substrate coming off the press through a heating zone on a continuously moving belt. Its main sections are as follows:

  • Infeed section: the part where the piece coming from the printing machine is transferred onto the belt. Having it at the same height as the bed of the printing machine allows the wet print to pass across without being jolted.
  • Conveyor belt: a heat-resistant belt, usually Teflon-coated glass fibre mesh or similar. The mesh construction allows air to circulate beneath the substrate as well. The belt is driven by a variable-speed motor and gearbox.
  • Heating section: the enclosed chamber that houses the hot air, infrared or UV sources. The body is insulated to reduce heat loss and has covers that open for maintenance.
  • Air circulation and exhaust: fans circulate the hot air inside the tunnel; an exhaust outlet discharges the solvent vapour and moisture to the outside.
  • Cooling section: the part at the end of the tunnel fitted with fans that blow ambient air from above.
  • Controls: temperature and belt speed are set and monitored from here.

The dwell time of the substrate in the tunnel is found by dividing the length of the heating section by the belt speed. For example, if the belt travels at two metres per minute through a four-metre heating section, the piece stays under the heat for two minutes. To achieve the same drying time at a higher production speed, the tunnel has to be longer. This is why tunnel length determines capacity.

Why is a cooling section necessary?

A piece leaving the tunnel is hot. If hot pieces are stacked straight away, several problems arise: the ink is still soft and sticks to, or marks, the back of the piece above it; plastic materials deform when stacked while hot; in materials such as glass, sudden and uneven cooling creates stress; and the operator cannot handle the hot piece by hand.

In the cooling section, fans blow ambient air over the piece and it comes down to a temperature at which it can be stacked or go on to the next colour. In multicolour work this matters for a further reason: a second colour printed onto a hot piece can cause the ink to dry in the screen and the registration to drift, because the heated substrate has expanded.

How are the right temperature and speed set?

Setting up drying is a balance between two variables: temperature and time. A higher temperature calls for a shorter time, a lower temperature for a longer one; but this relationship is not unlimited. Too high a temperature damages the substrate, makes the surface of the ink skin over and trap the solvent beneath it, or causes the colour to yellow. When making adjustments, the following sequence can be followed:

  1. Take the temperature and time recommended in the ink's technical data sheet as your starting point.
  2. Find out the highest temperature the substrate can withstand and stay below it.
  3. Bring the tunnel up to operating temperature; the first prints run through a cold tunnel will be under-dried.
  4. Set the belt speed so that the piece remains in the heating section for the recommended time.
  5. Run a test print through the tunnel and check it using the tests below.
  6. If the result is inadequate, reduce the belt speed first; if it is adequate, increase the speed in steps to find the limit of capacity.
  7. Record the values you have found together with the substrate, ink and colour details.

The temperature shown on the tunnel's display is the air temperature; the actual temperature at the surface of the substrate may differ from it. Surface temperature is measured with a non-contact infrared thermometer, with temperature indicator strips, or with temperature probes that travel along the belt with the piece.

How can you tell that the print is dry?

Drying and curing are verified by testing, not by eye. The commonly used methods are as follows:

  • Touch and stacking test: once the piece has cooled, the surface should not be tacky, and pieces placed on top of one another should not mark each other.
  • Tape test: adhesive tape is pressed firmly onto the print and pulled off sharply. If ink transfers to the tape, adhesion is inadequate. In a more rigorous version, the print is first scored in a fine cross-hatch pattern and the tape test is then carried out.
  • Fingernail and scratch test: the ink should not lift easily when scratched with a fingernail or a hard point.
  • Solvent rub test: the print is rubbed with a cloth soaked in a suitable solvent. Cured ink does not dissolve or is affected only very slightly; uncured ink transfers to the cloth.
  • Stretch test: in textiles, a plastisol print should not crack when stretched. If it cracks, the bottom layer of the ink has not cured.
  • Wash test: for textile prints, this is the test that best reflects real conditions of use.

Many inks reach their final durability in the hours after leaving the tunnel, and some over a period of days. When the tests should be carried out is also stated in the technical data sheet.

Common drying mistakes

  • Dry on the surface, wet inside: the temperature has been set high but the time kept short. The surface skins over, the solvent underneath is trapped and the print later blisters or stays soft. Lower the temperature and extend the time.
  • Sticking in the stack: cooling is inadequate or drying is incomplete. Check the cooling fans and the belt speed.
  • Warping and shrinkage of the substrate: the temperature is above what the substrate can withstand. Lower the temperature and, if necessary, work at a lower temperature in a longer tunnel.
  • Yellowing or dulling of the colour: there is excessive heat or the piece is spending too long in the tunnel. Pieces left beneath the heaters when the belt stops are particularly at risk.
  • Edges dry, centre wet: heat distribution in the tunnel is uneven, or the belt is narrow for the piece. Run the piece down the centre of the belt and check the air distribution.
  • Starting production with a cold tunnel: the first pieces through before the tunnel has reached operating temperature are under-dried. Wait for the warm-up time.
  • Exhaust closed or inadequate: solvent vapour builds up in the tunnel, drying slows down and the air in the working environment deteriorates.

What should you look for when choosing a drying tunnel?

A tunnel is an investment that needs to be considered together with the printing machine. The deciding factors in the choice are as follows:

  • Belt width: it should be wide enough to leave a margin on both sides of the widest piece to be printed.
  • Length of the heating section: it should provide the dwell time the ink requires at the target production speed. If an increase in capacity is envisaged, a modular design that can be extended later is an advantage.
  • Heating method: it should suit the ink being used. If more than one type of ink is in use, hybrid systems should be considered.
  • Temperature control: being able to set the temperature digitally, hold it steady and divide it into zones gives repeatable results.
  • Belt speed adjustment: the speed should be steplessly adjustable over a wide range.
  • Cooling section: it is necessary if pieces are to be stacked at the outfeed or if multicolour work is being done.
  • Exhaust and ventilation: essential with solvent-based inks; the tunnel's flue connection and the ventilation of the workshop should be planned together.
  • Energy consumption and insulation: a well-insulated body reduces both the energy bill and the heat given off into the workshop.
  • Compatibility with the printing machine: infeed height, width and capacity should be determined according to the printing machine.
  • Ease of maintenance and safety: there should be opening covers, easily accessible heaters and fans, an emergency stop button and guarding against hot surfaces.

Maintenance and safety

A drying tunnel is a machine with relatively few moving parts, but it does need regular maintenance. The tension and tracking of the belt should be checked, and the belt adjusted if it is drifting to one side. Fan grilles and air ducts should be kept free of dust and the filters cleaned; a blocked air path both weakens drying and shortens the life of the heaters. The surfaces of infrared heaters and UV lamps should be kept clean, and the running hours of UV lamps should be monitored, because lamps lose power over time even though they continue to light.

As regards safety, in tunnels used with solvent-based inks you should make sure that the exhaust is running continuously, and flammable materials such as solvents and cloths should not be left around the tunnel. No substrate should be left beneath the heaters when the belt stops. In UV systems, the curtains that prevent light from escaping should be in place, and the lamp should not be looked at with the naked eye.

Rack drying or tunnel drying?

In small workshops, prints are often laid out on drying racks and left to dry on their own at room temperature. The initial outlay for this method is low, but it has serious limitations. Racks take up a great deal of space; the drying time varies with the temperature and humidity of the surroundings and can stretch to hours in the winter months; the prints are exposed to dust while they wait, and in multicolour work the same wait is repeated between every colour. With large-format and heavy substrates, glass sheets for example, carrying each piece to the rack both takes time and carries a risk of breakage and smearing. Moreover, rack drying only works for inks that dry by evaporation; inks that cure by heat or by light will not harden by waiting on a rack.

In a conveyor tunnel, by contrast, the piece moves onto the belt as soon as it leaves the printing machine and emerges from the other end within a few minutes, dried and cooled. The drying conditions are the same for every piece; they are not affected by air temperature or the season. Production flows continuously, with no need for intermediate stock or rack space. As daily quantities rise or piece sizes grow, the tunnel ceases to be a luxury and becomes the core machine that sets the pace of production.

Ways to reduce energy costs

The drying tunnel is the most energy-hungry part of a screen printing line. A few simple habits bring this cost down noticeably:

  • Do not run the tunnel hotter than necessary; going above the value in the technical data sheet does not improve quality, it only increases consumption.
  • Plan jobs so as to reduce the time the tunnel spends running empty. Print jobs that need the same temperature one after another.
  • During long breaks, turn the heaters down or off; but when restarting, wait for the tunnel to reach operating temperature.
  • Keep the body covers and insulation in good order; a cover left open leaks heat continuously.
  • Do not open the exhaust more than necessary. The exhaust is needed to remove solvent vapour, but excessive extraction also throws heated air out.
  • Keep the fan grilles and filters clean; a blocked air path means a longer time and more energy for the same drying.
  • Lay the pieces on the belt without leaving unnecessary gaps between them; as the fill rate of the belt rises, the energy per piece falls.

Conclusion

Drying is the unseen but most decisive stage of screen printing. A well-printed job loses its value when it is badly dried. Getting drying right comes down to knowing how the ink hardens, choosing the heating method that suits it, balancing temperature against time and verifying the result by testing. A conveyor drying tunnel that is sized to the capacity of the printing machine, has a cooling section and offers repeatable settings safeguards both quality and production speed.

Arus Makina offers conveyor drying tunnels that connect to the outfeed of the printing machine and consist of drying and fan-cooling sections. Write to us with the ink you use, your substrate and your target production speed, and let us work out together the tunnel size that suits your work.

Which machine fits your work?

Tell us what you print and at what size, and we will send a suitable model and a quote.

Request a Quote

More articles